MyPage is a personalized page based on your interests.The page is customized to help you to find content that matters you the most.


I'm not curious

Steps to Make Tangle Free Headphones with Embroidery Floss

Published on 18 March 17
900
0
0
Look for cracked wires or rips within the protective cover. Instead of spend the following twenty to thirty minutes covering your headphones with embroidery thread, simply to ask them to break tomorrow, check their condition first. Toss any pair that's on its last legs and purchase a new set.

Measure your headphones, such as the Parrot Zik 3.0 Wireless and Sony H.Ear Wireless headphones. This will help you to have the most accurate fit.

Cut the thread to size based on your measurements. Ensure you create a clean cut so it's not necessary unraveling thread at the bottom of the wires.

Cut some extra thread, just in situation.

Double knot the strings and wire them together. Consider beginning in the base area where your headphones will plug to your sound system (or ipod device).

Stabilize the headphone wire. Put the headphone wire having a knot either in a clipboard to stabilize it or tape it lower to some hard surface. You do not need it getting around or sliding while focusing on the wrapping.

Divide the strings into threes, departing the headphone wire in the centre.

The division into three is suggested however, you can divide it more if wanted.

Braid. Mix one color string within the other string. Then mix it underneath the third. Pull the thread with the loop and push the knot up toward the very best knot.

Continue weaving exactly the same string within the same fashion roughly ten to fifteen more occasions, pushing the knot upward.

Grab another color string and carry out the same action of weaving it under and also over another two strings. Keep your headphone wire in the centre so it starts to be consumed through the string.

Wrap until you're able to one finish from the headphones. Determine which earpiece (right or left) is going to be completed using the pattern and tie a dual knot toward the ear piece to secure it into position.

Trim off any loose string which means you don’t get string inside your ear if you use your headphones.

Begin the procedure in which the first pattern split off, to pay for sleep issues from the headphones.

Tie a preliminary double knot after which start to weave the 3 strings along with the headphone wire in the centre.

Cut and tie another finish exactly the same way while you did the very first finish. Remove any loose strings.
Steps to Make Tangle Free Headphones with Embroidery Floss - Image 1
Look for cracked wires or rips within the protective cover. Instead of spend the following twenty to thirty minutes covering your headphones with embroidery thread, simply to ask them to break tomorrow, check their condition first. Toss any pair that's on its last legs and purchase a new set.

Measure your headphones, such as the Parrot Zik 3.0 Wireless and Sony H.Ear Wireless headphones. This will help you to have the most accurate fit.

Cut the thread to size based on your measurements. Ensure you create a clean cut so it's not necessary unraveling thread at the bottom of the wires.

Cut some extra thread, just in situation.

Double knot the strings and wire them together. Consider beginning in the base area where your headphones will plug to your sound system (or ipod device).

Stabilize the headphone wire. Put the headphone wire having a knot either in a clipboard to stabilize it or tape it lower to some hard surface. You do not need it getting around or sliding while focusing on the wrapping.

Divide the strings into threes, departing the headphone wire in the centre.

The division into three is suggested however, you can divide it more if wanted.

Braid. Mix one color string within the other string. Then mix it underneath the third. Pull the thread with the loop and push the knot up toward the very best knot.

Continue weaving exactly the same string within the same fashion roughly ten to fifteen more occasions, pushing the knot upward.

Grab another color string and carry out the same action of weaving it under and also over another two strings. Keep your headphone wire in the centre so it starts to be consumed through the string.

Wrap until you're able to one finish from the headphones. Determine which earpiece (right or left) is going to be completed using the pattern and tie a dual knot toward the ear piece to secure it into position.

Trim off any loose string which means you don’t get string inside your ear if you use your headphones.

Begin the procedure in which the first pattern split off, to pay for sleep issues from the headphones.

Tie a preliminary double knot after which start to weave the 3 strings along with the headphone wire in the centre.

Cut and tie another finish exactly the same way while you did the very first finish. Remove any loose strings.

Steps to Make Tangle Free Headphones with Embroidery Floss - Image 1

This blog is listed under Peripherals Community

Related Posts:
Post a Comment

Please notify me the replies via email.

Important:
  • We hope the conversations that take place on MyTechLogy.com will be constructive and thought-provoking.
  • To ensure the quality of the discussion, our moderators may review/edit the comments for clarity and relevance.
  • Comments that are promotional, mean-spirited, or off-topic may be deleted per the moderators' judgment.
You may also be interested in
 
Awards & Accolades for MyTechLogy
Winner of
REDHERRING
Top 100 Asia
Finalist at SiTF Awards 2014 under the category Best Social & Community Product
Finalist at HR Vendor of the Year 2015 Awards under the category Best Learning Management System
Finalist at HR Vendor of the Year 2015 Awards under the category Best Talent Management Software
Hidden Image Url

Back to Top